Wuxi Huatong Pneumatic Manufacture
Pneumatics/Solenoid Valve/Cylinder
Key considerations for directional control valve selection:1. Port Size Selection: Based on actuator flow rate at operating pressure. Manufacturers may specify flow as Free Air (ANR) or at pressure (e.g., 0.5 MPa). Valve thread size ≠ port size. Select valve flow capacity slightly above system demand. For pilot/signal valves: use 3mm port for distances ≤20m or few valves; 6mm for >20m or multiple valves.2. Function & Control Method: Match positions, ports, memory function, and rest state to system needs. Substitute if necessary (e.g., block unused ports on a 5/2 valve to mimic 3/2)—though not ideal for new designs.3. Operating Conditions: Ensure compatibility with system pressure, power supply (AC/DC, voltage), fluid temperature, and ambient conditions.4. Performance Requirements: Consider minimum operating/control pressure, response time, leakage rate, life cycle, and reliability. For high-seal applications (e.g., inert gas systems), choose spool-type valves to prevent cross-port l...
根据无锡市政府“退城进园”的工业调整布局步骤，我公司被列无锡市工业布局调整第一批企业（27家）之一。 2006年8月，公司已整体搬迁至无锡市惠山经济开发区内的惠山大道东侧欣惠路555号。 邮政编码：214177。 欢迎各位新老客户光临！联系电话：0510-85752151 传真：0510-85757700
A solenoid valve is an electromagnetically controlled valve used in industrial systems to regulate the direction, flow rate, speed, and other parameters of media such as water, oil, or air.By integrating with different electrical circuits, solenoid valves enable precise and flexible control. Various types exist—safety valves, check valves, control valves, shut-off valves—each serving distinct roles in automation systems.Basic Working Principle:Inside the valve is a sealed chamber with ports connected to different fluid lines. A plunger (or spool) sits in the center, flanked by one or two electromagnetic coils. When a coil is energized, it attracts the plunger, opening or closing specific ports. This directs fluid into selected pathways, where pressure acts on a cylinder piston. The piston drives a rod, which in turn actuates mechanical devices. Thus, by switching the solenoid current on/off, mechanical motion is precisely controlled.
1. Critical: Clean and purge pipelines thoroughly before installing the solenoid valve to prevent debris from blocking orifices or damaging sealing surfaces. Install a filter (e.g., from Wuxi Huatong Pneumatic) if micro-contaminants are present.2. Align the flow arrow on the valve body with pipeline fluid direction. Mount the coil vertically upward or horizontally.3. Verify that system pressure, temperature, and supply voltage match the valve’s nameplate ratings.4. Ensure medium cleanliness. Periodically clean internal components and inspect seals—replace if damaged.5. During installation, use a wrench on the valve body—not the coil—to avoid internal deformation.6. After installation, cycle the valve several times with fluid to confirm proper operation before commissioning.7. Follow the wiring diagram provided.8. Install pressure gauges upstream and downstream to monitor system pressure.9. For critical systems, install a bypass line to isolate the valve during maintenance. If insta...
QGS Series Cylinder Mounting Configurations:The QGS standard cylinder complies with ISO international standards for dimensions, mounting forms, and interfaces—ensuring reliable operation, durability, and interchangeability. Available mounting types:Unmarked = Basic typeMF1 – Head flange mountMF2 – Cap (rear) flange mountMS1 – Axial base mountMP2 – Rear detachable double clevis mountMP4 – Rear detachable single clevis mountMT4 – Intermediate trunnion (pivot) mountLZ – Piston rod clevis jointFC – Piston rod wiper boot
Directional control valves (reversing valves) change airflow direction by altering internal passages, thereby controlling the motion direction of pneumatic actuators. Types include: pneumatically piloted, solenoid-operated, mechanically actuated, manually operated, and time-delay valves.1. Pneumatically Piloted Directional ValveThese use air pressure to shift the main spool. By control method: pressure-actuated (signal pressure rises to shift), vent-actuated (signal pressure drops to shift), and differential-pressure actuated (spool shifts due to pressure difference across ends).By structure: poppet-type and spool-type. Spool-type valves resemble hydraulic directional valves. Here we focus on poppet design.Poppet Valve Working PrincipleFig. 1 shows a 2/3-way, single-pilot poppet valve. Without pilot signal at port K (Fig. a), spring and P-pressure keep P disconnected from A; A vents to T. With pilot signal at K (Fig. b), P connects to A, and A is isolated from T.Fig. 1: Poppet-type dir...
How to properly size and select a pneumatic cylinder?1. Bore Size:Based on your required load, select operating pressure and stroke direction, then calculate the appropriate bore diameter using standard formulas—or refer to cylinder force output tables.2. Stroke Length:Determine the required workpiece travel distance to define cylinder stroke.3. Cushioning Type:Choose between non-cushioned and adjustable cushion cylinders. Select adjustable cushioning if impact-free deceleration at stroke end is required.4. Lubrication Method:Options: lubricated or non-lube (oil-free). Use oil-free cylinders in contamination-sensitive industries like food or pharmaceuticals.5. Cylinder Series:Once the above parameters are set, select an appropriate series from Wuxi Huatong Pneumatic’s product catalog.6. Mounting and Connection Style:Choose suitable mounting accessories based on application and installation constraints.7. Magnetic Switches:Used for position sensing and signaling. Prerequisites: alumin...
Common solenoid valve faults include:(1) Loose or detached wire connections – simply tighten them.(2) Burnt coil – caused by moisture ingress (leading to excessive current) or insufficient coil turns (resulting in inadequate magnetic force). Remove the coil and test with a multimeter; replace if faulty.(3) Valve sticking – occurs when contaminants enter or lubrication is insufficient.(4) Air leakage – typically due to damaged seals; replace seals. Also inspect piping to rule out external leak sources.
Product Specifications K22JD-W K23JD-W K25JD-W Delivery: In stock Other: Best price available Electromagnetic Directional Control ValveWuxi Huatong Pneumatic Manufacturing Co., Ltd. Tel: 0510-83591123We offer a wide range of products with complete specifications, including: various cylinders, electromagnetic directional valves, air preparation units, auxiliary components, pneumatic machinery, integrated pneumatic systems, and industrial hydraulic cylinders. We also manufacture tilting mechanical presses, pneumatic presses, grinders, and specialized bearing production machines.Wuxi Huatong Pneumatic Manufacturing Co., Ltd. provides comprehensive solutions—from pneumatic control and actuation components to air treatment, auxiliary parts, machinery, and turnkey systems. With advanced equipment, refined processes, and rigorous testing, our products enjoy an excellent reputation nationwide and are exported to Europe, America, and Southeast Asia. Our commitment: first-class technology, qual...
产品规格 M1420万能外圆磨床，带内磨头交货方式 现货（请联系确认） 其它 *优惠价 M1420 万能外圆磨床，带内磨头无锡市华通气动制造有限公司 0510-83591123 M1320型外圆磨床，用于磨削各种中小型零件的圆柱、圆锥形外圆及端面，同时适用于橡胶棍的磨削。 M1420为万能外圆磨床，除能实现M1320的全部功能外增加了内磨功能，可磨削圆柱孔及圆维孔。 本系列磨床具有高效率、高节奏、高精度等特点，其性能优越、工作可靠，外形美观，是适用性强的经济型磨削设备。 M1320 cylindrical grinder is designed for grinding cylindrical or tapered surface of the small parts, and rubber stick. M1420 is universal cylinder grinder machine, more function than M1320, such as inner grinding , cylinder hole grinding . This series grinding machine features efficient, high speed, good precision. working stable. High performance-price ratio equipment.
